Facade plaster Aquasloy Volma

Rybnikov Alexey

Surface plastering - preparation of a building base for decoration. To finish lasting more than one year, you need to use only high-quality building materials. One of such tools is Plaster Volma Layer marked "aqua". Due to its good characteristics and wide scope of application, the product is popular with craftsmen.

Plaster Volma Aquasloy

Material Description

Aquma Volma is a stucco mixture, the main component of which is Portland cement. The composition of the product also includes mineral and polymer additives, lightweight fillers that improve the characteristics of the material. The product has moisture resistance, increased strength and does not crack after solidification. The composition is intended for manual application. The material is recommended for use in facade decoration, in dry rooms and in rooms with high humidity and lack of heating.

Specifications

Volma Layer plaster with the prefix "Aqua", the flow rate of which is indicated on the package, has the following technical characteristics:

• recommended layer thickness - 30 mm for walls, 10 mm for ceilings;
• maximum layer thickness - 60 mm;
• tensile strength in bending - 2.0 MPa;
• compressive strength - 4.9 MPa;
• maximum dimensions of fractions - 1.25 mm;
• the viability of the product in finished form - 120 minutes;
• the amount of liquid per 1 kg of dry product is 0.28-0.3 l;
• frost resistance - 35 cycles;
• withstands temperature extremes from -40 to +60⁰WITH;
• the time of complete solidification is 3-7 days.

Specifications

Area of ​​use

Plaster front Volma Aquasloy is applied:

• for leveling the surface outside and inside the building;
• for plastering walls or ceilings in unheated rooms;
• to mask defects in the construction base;
• for plastering walls or ceilings;
• before facing the surface with tiles, including in the kitchen, bathroom and other rooms with high humidity;
• for painting for even application of paints and varnishes.

Façade plaster Volma Aquasloy is used for the following types of building bases:

• slag, expanded clay, foam and aerated concrete;
• concrete;
• old plaster;
• brickwork.

Using masonry material

Application Conditions

Plaster mixes Volma Aquasloy are used for decoration under the following conditions:

• air temperature - from +5 to +30⁰WITH;
• the material cannot be dried artificially using heaters and other similar devices;
• when using material for exterior decoration, it is recommended to cover the composition with a plastic film to protect it from rain until the product solidifies;
• Do not apply plaster in cloudy and windy weather.

Material consumption

The consumption of Volma Layer plaster with the prefix “aqua” is indicated by the manufacturer on the packaging. This is an estimate. When calculating the required amount of material, it is recommended to take into account surface differences, the presence or absence of a defect and the type of building base. The approximate consumption of Volma plaster per 1 m2 when applying a layer with a thickness of 10 mm is 11-12 kg.

Storage rules

It is important that certain rules are observed when storing material. This ensures the safety of the quality and properties of the product. It is recommended to keep bags of material on wooden pallets in dry rooms.Before buying funds, it is recommended to check the storage rules. If they are not respected, it is worth purchasing plaster at another outlet.

Packing and cost

The product is available in 25 kg paper bags. The approximate price is 165 rubles per package.

Facade of the building after plastering and finishing

Application Technique

Fans who plaster walls or ceilings with their own hands are recommended to familiarize themselves with the algorithm of work.

Building foundation preparation

Instructions for preparing a building foundation before applying Aquasloy from Volma:

1. Remove the old coating.
2. Use a solvent to remove oil and grease stains from the surface.
3. Tap the construction base with a hammer, and when sprinkling material, increase the size of the defect.
4. Primer the surface twice, taking a break after each application of the primer.

If plastering will be carried out for a new building, then it is necessary to wait 28 days after the construction of the brickwork and 90 days after the construction of the structure from concrete.

Surface preparation for plastering

Solution preparation

Rules for the preparation of mortar for plastering:

• pour cold water into the bucket at the rate of 0.28-03 liters of water per 1 kg of dry powder;
• add plaster;
• using an industrial mixer (as in the photo below) or a drill with a mixer nozzle, knead the solution until a uniform mass of thick sour cream is formed, if necessary, you can add liquid as the product mixes;
• leave the product for 5 minutes and stir again;
• use the finished plaster for two hours, otherwise the solution will harden.

When preparing the solution it is important to follow the sequence of work. This ensures the preparation of a quality composition that will have the appropriate characteristics.

Mixing plaster

Surface plastering

If Volma Layer plaster with the prefix “aqua” is used for decoration, the instructions for applying the material will be as follows:

1. Using a trowel, bucket or trowel, throw the solution on the surface and distribute the product on the base using the rule.
2. Stop the finish until the material solidifies.
3. Using a two-meter level, check the vertical differences of the building base - the permissible error is 5 mm.
4. Cut off the roughness of the plaster.
5. Dampen the material using a brush.
6. Clean the surface with a building grater to remove any stains that remain after applying the rule, as well as minor bumps.
7. Primer the base.
8. Apply the topcoat.

In the video in this article, the masters show how to properly use the material for plastering the surface.

Plaster Aquasloy from Volma is a high-quality building material that has a wide scope and guarantees a long operational period of decoration without the need for restoration.