How to glue the wallpaper on the fiberboard with your own hands

Gusevsky Andrey Anatolyevich

How to paste wallpaper on a fiberboard

How to paste the wallpaper on the fiberboard thinks a lot of owners before starting repairs. After all, improperly performed work, the coating will not last long and will peel off quickly.

Today we will tell you how to paste wallpaper on a fiberboard and at the same time do everything efficiently and reliably. You can see certain moments in the photo and video and then you will finally understand everything.

Doing wallpaper on a fiberboard

Sticking wallpaper on a fiberboard is not at all complicated. Everything can be completely done with your own hands. See below for instructions on this. Here you just need to follow some rules and not rush.

If there are fears that it will not work out qualitatively, you can turn to a trusted master. So you definitely save time and energy.

We pay attention to possible problems.

There are problems and there is no need to hide them:

• Hardboard perfectly absorbs moisture from the air. The glue that we apply to the wallpaper, it also absorbs itself well. However, with such properties, one can hope for good adhesion.

Attention: Hardboard, as soon as it absorbs the greatest amount of moisture, will warp and deteriorate.

This level of moisture leads to the fact that the wallpaper will begin to go in waves along its surface.

• The seams that are between the fiberboard will be visible under the wallpaper of small subtlety. Swelling sheets will be even more striking: the dimensions of such surfaces, due to their ability to absorb all moisture from the air, will change in the most unexpected way. However, when gluing thick wallpaper such waves can be slightly covered.
• Now let's think about the method of fastening hardboard. We use either nails or self-tapping screws, right? Often even un galvanized. After what time, any nail is a potential source of corrosion and rust.

We develop solutions to problems

How do we stick wallpaper with all the flaws?

Paint the walls

The difficulties of hygroscopicity and the appearance of corrosion can be avoided if we ground our surface, which serves as the boundary between the adhesive and the base. The particle itself takes its place here, so there is no need to prime too deep into the surface.

Many people ask the question, is it possible to glue wallpaper on fiberboard and for what reasons this can not be done? Let's go over its constituent elements. A large mass of the total volume of the primer is a water base. But we want less to come into contact with her at all.

And if we take alkyd primers or colorful material for our work, then they will work best. They will cover all fiberboards and fasteners with a thin film that has excellent waterproofing properties, its surface itself after making small changes that we will make in the preparation of the glue will enable us to provide good contact with a clean surface.

In general, the design itself includes two points:

1. We paint the entire surface of the fiberboard (cm. Painting walls in an apartment: how and how to perform) Paint is best taken in white, as it is necessary that it is invisible under the wallpaper. To do such work is better in two layers. Carefully paint the seams and fasteners themselves.
2. We add PVA glue to the glue itself for our wallpapers (no matter what we purchased in the building materials store). We expect it in the amount of half a liter per bucket.

True, we have a significant drawback, because the relief of the seams is perfectly visible through the wallpaper. How do we deal with these difficulties?

Putty

Our fallback is that we will putty the entire hardboard surface (see Puttying the walls under the wallpaper with your own hands) It is noticeable that one should not even think about a good and tight contact between this layer and fiberboard. Is this a hopeless situation?

No, it is not. The following materials will come to our aid:

1. We take already used PVA glue.
2. We need another grid with small cells.

How to paste wallpaper on a fiberboard at home and carry out preparatory work for repair using the above materials:

1. We make the soil in the form of PVA glue and put it on our surface for gluing. The price of glue is very small, in the amount of fifty rubles per kilo, so our budget will not suffer much from such actions. There is no need to dilute the glue, we will try to bring to a minimum level the degree of change of the hardboard itself.
2. Glue fiberglass into our layer in small cells. We can safely apply glue directly to the fiberboard. Through small holes and niches, glue gets to the base itself.
3. Next we put gypsum putty. The best thickness for such work is one millimeter. If you have not previously been involved in repairs, it will be possible to apply several thin layers.
4. We carry out grinding to eliminate defects.
5. We put the soil on the base.
6. Papered with standard glue.

An interesting fact is that with the next repair the wallpaper can be removed very easily and simply. It will only be necessary to moisten them a little and their entire layers will be torn off without any effort.

We use drying oil as soil

The previous method of preparatory work has one obvious flaw. We protect our surface from liquid only from its frontal part, however, if the room has a high level of humidity, then visible changes will appear sooner or later.

Apply soil to the fiberboard

The best way to eliminate this effect is to impregnate the fiberboard with drying oil from both its parts.

Such repairs can be carried out in two ways:

1. We apply hot drying oil directly to the material.
2. First, we apply cold drying oil, which is heated by a special hairdryer or other units of a similar purpose.

After such work, the material is no longer afraid of either excessive moisture or direct contact with water. Let's not forget that drying oil interacts poorly with putty, glue will also lie badly on it. What should we do in this situation?

To help we take contact concrete, sand from quartz is included in its composition. The base of polymeric substances gives good contact with the most difficult surfaces, while sand has the property of creating bumps and roughness. Thus, any plaster will lie like a glove.

Next, we finish the surface according to the standard scheme:

1. Putty putty. We do not make reinforcing seams.
2. As soon as the putty dries, we put the soil on it in the form of a penetrating layer. Now we are waiting for it to dry. Only then we are waiting for the wallpaper itself.

Wallpaper Adhesive Buying Tips

All construction and repair work directly depends on the quality of the adhesive:

• When purchasing glue, you need to pay attention to the type of wallpaper. If the paper option, then feel free to buy any glue. For example, for fabric wallpapers it is better to take a vinyl mixture. It is very comfortable, since defects and imperfections can occur in the work. With this type of glue, their correction will be very easy: the wallpaper is simply carefully removed from the surface of the wall, and then, after making adjustments, put back. In such cases, we do not apply glue several times.
• In order for the heavy wallpaper to be well glued, you need to purchase a special glue of the desired composition in the store, where antifungal substances are included in its structure.However, it has one minus - the price for such a high-value product. However, its advantages overlap the disadvantage, it has a high level of resistance to moisture and is very durable.

Glue wallpaper on fiberboard yourself

The process of wallpapering on fiberboard in no way differs from the same types of work of other surfaces from a wide variety of materials.

How to glue a wallpaper on a fiberboard schematically

• We put glue not on the wallpaper itself, but on the base of the fiberboard surface. Since the moisture will be absorbed very much, we apply a large amount of the mixture to the sheet. The most optimal option for repairs will be a universal adhesive that protects the surface from the appearance of a fungus in the future, since it includes special fillers.
• We get glue in the building materials store with a large supply (as well as the wallpaper itself. So, it’s simply impossible to accurately calculate the amount of use during work. After gluing the wallpaper, we must wait two days for it to dry. Therefore, we must not open all the windows and shutters this entire period of time, otherwise we can see the swelling of the working surface and even the peeling off of the wallpaper itself from the wall.
• Once they are fully dry, they are varnished.

Problems when wallpapering our surface

Any person who glued wallpaper understands that the process of such work is very necessary and sometimes can not do without the difficulties of one sense or another. It is necessary to spend a lot of strength and energy during the repair.

• To speed up the process, you can take a partner. The second person will help you, for example, maintain the second edge of the canvas and look at the level of evenness during such work.
• The most difficult task is to glue wallpaper in the corners. We will need to make the joints of the parts, then cover the resulting seam with a corner. The corners inside can be glued with wallpaper and overlap.

Attention: We want to note that a clear standard method for this type of finishing work has not yet been invented and created. It can transform due to different materials, surface color, and the presence of images.

Thus, whether it is possible to glue on a fiberboard wallpaper you already know, this is a very responsible job, where you must reckon with all the complexities and subtleties. If you do everything yourself, then the final price will not be high.