Wall Decoration with Plastic Panels: Proper Work
In this article we will understand how to decorate walls with plastic panels, what is the technology of this process, and also get a number of useful tips on this topic. This finish is perfect for decorating the bathroom and cottage.
Wall plastic panels for interior decoration are often used in the decoration of any kind of premises. You will have the opportunity to see photos and videos on this topic and immediately see how this is done.
The content of the article
Material advantages
This finish can perfectly suit many types of rooms. But sometimes it may not suit the owner.
In any case, you should first learn more about this type of material:
- With such a finish you do not need to do a full wall decoration. And it will significantly save time and finances. Only standard surface preparation is required;
- You can always hide all communications that are on the plane. Only this must be calculated in advance.
After all, then your useful area will become less; - You can always make additional wall insulation, and this is important, the more it will go, as an addition to the work;
- You can do all the work completely with your own hands and without resorting to outside help. And this will significantly reduce the cost of the entire structure;
Caution: Panels are not afraid of water. But you should think that they are suitable for decorating a steam room.
Everything is good in moderation. When buying material, you should give preference to trusted brands.
Remember, cheap Chinese manufacturers can supply not only not high-quality products, but also harmful to your health.
Surface preparation
Before performing work, you should properly prepare the surface:
- To begin with, you should remove all the old coating. To do this, use a brush for metal;
- We do inspect the plane. If we have exfoliation of the previous coating, then it should be removed with a hammer and a chisel;
- Now you should do the surface treatment with antiseptics. It is worth doing even for the sake of prevention.
If the fungus begins to appear, then it will be eliminated and difficult; - After this, it is necessary to apply a primer to the surface, for this we use a brush or spray;
- Now we need to make the marking of the profile fastening along the installation contour. This will be the harness, which should be in the same plane.
To do this, take oats and look at the evenness of the wall. Put a mark; - After that, we add the thickness of the profile to the size, while taking into account the height of the insulation and put a mark;
- Now we need to combine all the risks. To do this, take kapron thread and beat off the size. We got a profile placement outline.
Instructions will be given below. But before installation, you should know how to install and what material you need to purchase
We carry out wall decoration
The price of wall plastic panels for interior decoration has a fairly large expansion. It directly depends on the quality of the materials themselves and the technology of decorating the outer layer, the quality of which directly affects the durability of the use of panels and their preservation of good appearance.
Attention: When choosing panels of one manufacturer, it should be understood that the cheapest will last less time than their more expensive counterparts. And do not buy cheap Chinese products. You can also harm your health.
The technology of wall decoration with plastic panels is not so complicated, but it needs to be known. The panels are mounted on a frame that can be made of metal or wood.
It only depends on your desire.
Attention: If you are applying the second option, then you should bring the material to the place of work in advance and do the processing with antiseptics, which are available on the market. Make it a must. Prefer deep penetration fluid and allow the material to dry completely before installation.
We make a frame from a metal profile
Wall decoration with plastic begins with the performance of this particular work, which will fully determine the correct placement of the plane. We already have a fastening contour, now we need to fix everything correctly.
Attention: Using the frame will reduce the size of the room by at least 50 mm on each side. Also, the frame method will increase the cost of materials for wall decoration.
Before installation, you should immediately determine the insulation, which can be of different thicknesses. It can not be pressed with panels, then it will lose its properties. This should be taken into account when marking.
So:
- We cut the guide profile to the desired size and make it fastened. A self-tapping screw is also suitable for a wooden wall, but with concrete or brick, you should first make a hole with a puncher and then make a connection to the dowel.
Do not use the dowel from the sets. They will not give the necessary rigidity.
After all, the design has not a small weight. Buy separately the plastic and the screws to it, a couple of mm more from the hole in the plastic.
It is such a connection that will provide the desired quality; - Now do the installation of the rack profile. It must be fixed in one plane.
For the correct execution of work, you need to pull the fishing line along the diagonals of the harness. So it will be easier for us to maintain the plane of installation;
Caution: During installation, the length of the panels should also be considered.
Docking is not performed on weight, but is done only on a hard surface. Also remember that the installation of panels is perpendicular to the fastening of the profile. Make no mistake.
- After marking, we cut to the desired size and fix the rack profile with an interval of 500-600 mm. A simple rule works here: the smaller the interval between the rack profiles, the more reliable the plastic for wall decoration will hold and the overall design will be stronger.
The rack profile is inserted into the guides with the ends and fixed in them using a self-tapping screw.
Attention: Profile length - 3000 mm. If the width of the wall is greater, then you should pre-purchase a direct profile connector.
- After installing the frame, you should mount the insulation. Remember, it should not be deformed by a plane. Provide a clearance of a couple see
Installing a wood frame is done in exactly the same way. Only one detail to consider.
Do not fasten the planks to the walls in a dense. It is necessary to provide a tolerance of a couple of cm and this will save you from trouble during the expansion of the material with a temperature difference.
We do the adjustment of the transverse frames with the help of gaskets.
Making the lighting layout
After installing the frame, we need to make wiring for sockets or lamps:
- We determine the connection location and install the junction box. Which should be freely available, in case of a malfunction;
- Now we connect the cable and fasten it. To do this, we use terminal blocks that will make the connection high-quality and reliable.
It is not necessary to use twists in joints. It can only do harm; - In places of output, we release the cable. It should be enough to connect, and not end-to-end, but provide for a supply of wire.
Panel Installation
We can say that the most difficult work is already behind us and now we have to decorative wall decoration do it yourself plastic panels - fasteners panels directly on the profile frame. For this we use screws.
We start paneling from the corner from the window. Here, the light just falls correctly and all malfunctions are fully visible.
So:
- We fix the inner corner, which has a groove for installing the panel;
- Insert the edge of the panel with a smaller (thicker) protrusion into the already attached inner corner.
- Be sure to align the first panel with a level. We do this without fail, on the first panel the subsequent fastening will go and it will determine the correct direction;
- We fasten the other edge of the panel (with a large thin ledge) to the frame with a self-tapping screw.
- We insert the next panel into the first one so that the gap between them is not visible.
- We fix the second panel, etc. repeat these steps with the rest;
- In places of outlet sockets do as follows. We try on the panel and mark the place of output of the lamp.
After that, we make a hole on a flat plane, for this we use a grinder with a nozzle, only it should be purchased in advance. We make a hole without strong pressure, otherwise the material will begin to tear and you will damage the outer plane; - The last panel is rarely included in the whole and it needs to be cut in length. To do this, try on first and mark on the two edges with a pencil.
After that we connect them with the help of a staff and draw a cut line and make it with a hacksaw with a small tooth. After that we do fastening.
Attention: When attaching PVC panels to the frame, do this extremely perpendicularly. If the self-tapping screw went wrong, then do not fasten it to the same place. Pull back one cm and make a connection.
- Plastic wall decoration can use simple plastic corners, which are fixed with the help of a special adhesive "Liquid nails for PVC." Apply glue pointwise to the surface of the corner and press it to the glued surface.
To dry completely, it is best to fix it with paper tape. - If you hide communications that require periodic access (taps from risers, water meters, etc.), then you should buy plumbing hatches of appropriate sizes in the store in advance.
- During the installation of the panels with a hacksaw, cut out the necessary opening in the plastic. After all the panels have been installed, insert the hatch into the cut-out opening.
If necessary, expand it with a sharp knife; - After complete facing of the plane, the baseboard is mounted on the ceiling. It will hide connection errors.
Now you know, wall decoration with plastic panels and not such a difficult job, if you know how to do it correctly.
The most important thing is not in a hurry in this matter and do the markup correctly. Much depends on this.
